Remove a door card adjust the window stop

Have you done so much to the car today that it just doesn't fit into one section, or are you too damn lazy to split it all up? Either way, this is the section for you.

Moderators: CalAltaDubber, kamzcab86

User avatar
Briano1234
Whats that smell?
Posts: 3953
Joined: Mon Mar 21, 2005 6:45 am
What year is your cabby?: 1992
Do you own a Cabriolet?: No
Location: Duluth, Ga
Contact:

Remove a door card adjust the window stop

Postby Briano1234 » Thu Sep 13, 2007 4:43 pm

How do I remove my door card and adjust my electric windows?
Yes that is a 89 door that was cut and drilled to fit my 93.

1. Open your door, and remove the mirror adjuster knob

Image

2. Remove the 2 screws that hold the arm rest on and then turn the arm rest so that the upper handle is
parallel to the ground.

Image
Image
Image

3. Remove the door handle backing plate by inserting a flat blade screw driver in the tab and pry out.
Remove the screw, then lifting the handle remove the bezel from the door.

Image
Image
Image

4. Remove the 2 screws that hold the Speaker Grille/Speaker to the map pocket

Image


5. Remove the 3 screws that attach the door card to the door and disconnect the speaker wires/ connector

Image

6. Pry off the screw head cover to the rear of the map pocket, and then remove the screw.

Image
Image

7. Using your Special TOOL or gently using your hand pull on the bottom of the door card and you will
feel it give way and pop off, then work around from both sides and the top of the card.

Image
Image
[img]http:://i3.photobucket.com/albums/y65/briano1234/doorcard/Picture021.jpg[/img]

8. Take care to remove the connector from the Tweeter.

Image


9. Now remove the plastic, take care not to rip it. And you will be left with the door.

Image

10. Here are most of the adjusting 10mm bolts 2 on the bottom of the door and under the button hold the
rear rail and control the in and out of the window to the seal on the b pillar. There are 2 10mm nuts that hold the rear
window carrier to the rail. These will let you bring the edge up ot down a tad.

Image
Image

11. There are 3 screws that hold the upper slid to the door frame.

Image
Image
Image

12. The window stop is in the center of the cut out with the big sliding washer.
Position your window in to the frame and adjust the height by raising or lowering it a tad…
It should hit the top of the vent seal, but not move the vent frame.
Loosen the 10mm bolt and move the stop up, or down to the metal crank, and tighten.
Then open and close the door, to make sure that the window engages all the seals and doesn’t
interfere with the closure of the door.
Make sure that the window is fully engaged into the seal.

Image
Image
Image
Image

13. Once you are satisfied that the door is square to all the seals and the window opens and closes
correctly then replace the plastic and re-assemble in reverse order.
Briano

Yes as matter of fact, I have the Luck o'the Irish...everything I touch turns to fertilizer of the bovine variety.
You can lead a user to a link, but you can't make him Click.... :screwy:

User avatar
SoCal_Cabby
Postus-Whorus-Maximus
Posts: 2160
Joined: Sat Oct 11, 2003 2:49 pm
What year is your cabby?: 0
Location: Escondido, CA

Re: Remove a door card adjust the window stop

Postby SoCal_Cabby » Sun Oct 28, 2007 8:33 pm

nice write up :thumbup:


Return to “General Car Work”

Who is online

Users browsing this forum: No registered users and 1 guest